Your Questions

Taping protects surfaces from paint drips and splatters that can cause damage or are difficult to remove. It helps you avoid spending time and money doing rework or fixing damage after your paint project is done. It also helps you easily achieve professional-looking results with sharp paint lines.

See Prep & Tape Application to mask like a pro.

Taping protects surfaces from paint drips and splatters that can cause damage or are difficult to remove. It helps you avoid spending time and money doing rework or fixing damage after your paint project is done. It also helps you easily achieve professional-looking results with sharp paint lines.

See Prep & Tape Application to learn how to mask like a pro.

You should wait at least 24 hours before applying tape to a freshly painted surface, and choose a tape designed specifically for this application, such as ScotchBlue™ WALLS WOOD FLOORS.

This is usually caused by dirt and moisture which prevent tape from attaching to the surface.

See our Tape Won’t Stick page for some easy solutions.

ScotchBlue™ EXTERIOR Painter’s Tape is designed specifically for outdoor use. It has a sturdy construction and adhesive that can stand up to rainy weather, humidity, wind and direct sun.

3M recommends ScotchBlue™ WALLS + WOOD FLOORS Painter’s Tape for masking wood floors. Place rosin paper along the trim, and secure it to the floor along the baseboard.

See more at Protect a Wood Floor.

Remove tape when the paint is dry to the touch — typically one hour after application. If you are applying multiple coats of paint, don’t remove the tape until you have finished the last coat and it has had sufficient time to dry.

If the tape is still intact on the surface, use a hair dryer to loosen the adhesive, and remove all the backing from the adhesive.

Remove as much adhesive as possible by either rubbing the adhesive off with your finger, or by applying a fresh piece of tape over the adhesive to pull it up from the surface.

If residue remains, use a chemical-based cleaner. For Scotch® Masking Tapes try one or more of the following:

Citrus-based cleaners
Hydrocarbon solvent such as turpentine; a toluene-based cleaner

For ScotchBlue™ Painter’s Tapes, try one or more of the following:

Wallpaper and Paste Remover
Citrus-based cleaners
Ammonia-based cleaner

NOTE: Different tapes have different types of adhesive, so choose the cleaner carefully and test in an inconspicuous place before use.

When using cleaners, wipe with a cheesecloth or loose-nap fabric rags to allow the adhesive residue to imbed into the fabric.

After using cleaners, rinse surface with a generous amount of clean water.

If the adhesive residue has been on the surface for a long time or is highly cured, scraping may be required to break up the adhesive in order to remove it.

If ScotchBlue™ Painter’s Tape is used on or with a lacquer coating, the surface may react with the adhesive on the tape, making it difficult to remove. In this case, buffing or sanding may be required to remove the adhesive from the surface.

NOTE: Removing adhesive residue can put the surface it is adhered to at risk. If mechanical means (like scraping or abrading) are required to remove adhesive residue, most painted surfaces are at risk and have the potential to be damaged, regardless of the type of finish or level of cure time.

If you notice that paint is pulling up with the tape, or that paint is cracking along the paint line as you remove the tape, score along the edge of the tape with a razor blade before removing. This breaks the seal between paint and tape, ensuring a cleaner line and easier removal.

See Proper Tape Removal for a list of steps to follow when removing tape.

There are multiple reasons your tape may be slivering. If this happens, score along the tape edge with a utility knife, and then remove the tape. See how.

The recommended shelf life for masking tapes is generally one year.

ScotchBlue™ Painter’s Tape works well with:

Most water-based paints and coatings — acrylic, urethane, vinyl latex and enamels
Many solvent-based coatings — alkalyds, varnishes, most enamels and some polyurethanes
Plaster, glazes, textures and metallics used in faux and decorative painting

Be careful when working with lacquers. Nitrocellulose-based lacquers react with the adhesive on many painter’s tapes. They seem to bond the tape with the lacquer, making it impossible to remove the tape. Tapes with higher adhesion levels, such as tan masking tapes are a better choice for use with lacquers.